Active Aqua publishes 3,010 BTU/h for this model. Whether it is a good cold-plunge fit still depends on the tub heat load and whether the real plumbing loop can maintain 396–925 GPH.
Published specifications
| Cooling capacity | 3,010 BTU/h |
|---|---|
| Nominal label | 1/4 HP |
| Electrical input | 460 W |
| Flow requirement | 396–925 GPH |
| Connections | 1/2 in, 3/4 in |
| Environment | Indoor only |
| Manufacturer volume reference | 40-92 gal |
| ChillSizer data confidence | A |
Primary source: Hydrofarm / Active Aqua ↗
Model-specific design takeaway
A common DIY size. Flow is a hard gate: the calculator treats 396 GPH as the minimum manufacturer requirement.
| Gate for this exact model | Planning value | What can invalidate the choice |
|---|---|---|
| Thermal | 3,010 BTU/h published capacity | A real tub heat load or cooldown requirement above the conservative modeled capacity. |
| Hydraulic | Minimum 396 GPH; upper reference 925 GPH | Pump operating flow falling below the minimum after filter, hose, fittings and chiller losses. |
| Connections | 1/2 in, 3/4 in | Building the whole loop around a restrictive adapter instead of the practical system diameter. |
| Environment | Indoor only | Installing the unit where its documented environmental suitability does not apply. |
| Electrical input | 460 W recorded input | Ignoring manufacturer electrical instructions, circuit requirements or required protection. |
Source context: Manufacturer publishes 3,010 BTU/h, 396-925 GPH and a performance curve at 88°F ambient.
How to interpret the cooling capacity
This is a relatively small-capacity record in the database. It is most likely to fit compact, insulated, moderate-ambient systems; it should not be assumed to hold very cold targets in a large uninsulated tub.
Manufacturer publishes 3,010 BTU/h, 396-925 GPH and a performance curve at 88°F ambient.
ChillSizer does not treat nameplate BTU as perfectly constant at every water and ambient temperature. When a complete manufacturer capacity map is not available at cold-plunge conditions, the engine uses a conservative family-specific planning band and lowers confidence rather than presenting an invented exact curve.
Flow and pump compatibility
The manufacturer flow gate is 396–925 GPH. ChillSizer treats minimum flow as a hard system constraint. The pump must clear that requirement after hose, fittings, filter and internal chiller restriction — not at zero head.
The internal chiller pressure drop is also represented as a range when exact model-specific data is incomplete. A hydraulic PASS is therefore stronger than a single-point calculation: it survives both lower and higher modeled resistance.
Plumbing implications
Use the largest practical connection size supported by the chiller and pump. Long 1/2-inch runs, fine filter media and multiple sharp fittings can reduce operating flow quickly. A nominal adapter size on the chiller does not mean the entire system should be built at that smallest diameter.
Do not choose from the spec table alone. Run this model with the actual tub, pump, filter and hose.
Test this chillerInstallation environment
The record is marked Indoor only. An indoor-only or protected-installation unit should not be treated as outdoor equipment simply because the cooling capacity is large enough.
Also provide the ventilation/clearance required by the manual. Air-cooled refrigeration rejects heat into the surrounding air; a cramped hot enclosure can make the thermal problem worse.
What the confidence grade means
The data grade reflects source quality and how directly the published data supports the engine. A-grade records have strong primary specifications; lower grades indicate more interpolation or missing performance detail. Confidence is separate from whether the product is “good” — it tells you how much evidence supports the modeled inputs.
Frequently asked questions
Is 1/4 HP enough for a cold plunge?
Horsepower alone cannot answer that. Use the 3,010 BTU/h published capacity together with gallons, target temperature, climate and insulation.
What pump flow does this chiller need?
The recorded manufacturer requirement is 396–925 GPH. The pump must deliver that after the full system resistance.
Can I use this model outside?
This record is not treated as outdoor-rated by ChillSizer. Use a model explicitly intended for the installation environment.